攤鋪機攤鋪時加速攤鋪厚度是增加還是減少？實際上攤鋪機在攤鋪的過程中，要求是勻速的，熨平板是浮動在攤鋪物料上的。

Does the accelerated paving thickness increase or decrease when the paver is paving? In fact, during the paving process, the paver requires a constant speed, and the screed is floating on the paving material.

冷再生機出租廠家認為，換句話說，此時熨平板的合力是零，一旦加速，速度增加了，單位時間內熨平板攤鋪所需的物料沒有及時增加（機器反應有個過程），物料平均到走過的距離上就是減少了，所以攤鋪的路面厚度減小了，此時速度穩定后，熨平板有重新達到平衡的要求，厚度會慢慢的增加到原來的厚度。

The manufacturer of the cold recycling machine believes that, in other words, the resultant force of the screed is zero at this time. Once accelerated, the speed increases, and the material required for screed paving does not increase in time per unit time (there is a process of machine reaction). As a result, the average distance traveled by the material decreases, so the thickness of the paved road surface decreases. At this time, when the speed stabilizes, the screed has the requirement to regain balance, The thickness will gradually increase to the original thickness.

在現實的施工中，攤鋪與速度、溫度、物料配合比，施工的嚴謹程度都有關系。

In real construction, paving is related to speed, temperature, material mix ratio, and the rigor of construction.

攤鋪機的作業速度以輸分料保持勻速旋轉來確定攤鋪大行走速度。有規律的相應提高行走速值，夯錘數值，輸料數值，分料數值，使有規律的同時調高和調低，大的攤鋪速度不能使刮板和螺旋快速旋轉，這樣會使攤鋪面離析。

The operating speed of the paver is determined by maintaining a uniform rotation of the conveying and distributing materials to determine the large paving speed. Regularly increase the traveling speed value, rammer value, material delivery value, and material separation value accordingly, so as to regularly increase and decrease them simultaneously. Large paving speeds cannot cause rapid rotation of the scraper and spiral, which can cause segregation of the paving surface.

刮板和螺旋速度調整：根據攤鋪厚度和寬度，攤鋪速度三者相關，在主控制器中找出相應界面，先按50%設定，然后在攤鋪過程中，再根據攤鋪速度調整。

Adjustment of scraper and spiral speed: According to the correlation between paving thickness, width, and paving speed, find the corresponding interface in the main controller, set it by 50%, and then adjust it according to the paving speed during the paving process.

攤鋪機攤鋪過程中要能連續攤鋪,不能隨意停機,以免影響路面的平整度,當出現意外情況必須停車時,要將攤鋪機熨平板的防沉降鎖打開,以免熨平板下沉,再次起步時要將攤鋪機熨平板達到防爬鎖打開,以免熨平板前方的瀝青料溫度太低會將熨平板抬起,增大攤鋪厚度，影響路面的平整度。

During the paving process of the paver, it is necessary to be able to continuously pave and not stop at will to avoid affecting the flatness of the road surface. When an unexpected situation occurs and it is necessary to stop, the anti settlement lock of the paver's screed plate should be opened to prevent the screed plate from sinking. When starting again, the paver's screed plate should be opened to prevent the low temperature of the asphalt material in front of the screed plate from lifting the screed plate, increasing the paving thickness, and affecting the flatness of the road surface.

就攤鋪機的操作而言，在攤鋪過程中，還應注意盡量保持攤鋪的連續性和穩定速度，嚴禁時快時慢，盡量減少停機次數，嚴禁運輸車倒車時碰撞攤鋪機。必要時可以通過兩邊放線找平，利用縱坡攤鋪機縱坡儀，走鋼絲來控制平整度。

In terms of the operation of the paver, during the paving process, attention should also be paid to maintaining the continuity and stable speed of paving as much as possible. It is strictly prohibited to be fast and slow, minimize the number of stops, and prohibit the transport vehicle from colliding with the paver when reversing. If necessary, the flatness can be controlled by setting out and leveling on both sides, using the longitudinal slope meter of the longitudinal slope paver, and walking steel wires.

攤鋪機攤鋪時加速攤鋪厚度相關問題就講解到這里了，您對此有怎樣的疑惑或者需求，就來我們網站http://www.cifrimas.com咨詢了解吧！

That's all about accelerating the paving thickness when paving with a paver. If you have any doubts or needs about this, please come to our website http://www.cifrimas.com Consult and understand!